User manual BOSCH CIR24P00

[. . . ] CIW18P. . en Installation instruction Table of Contents Important Information . . 16 16 16 17 17 18 20 21 22 22 22 23 24 25 25 26 26 27 28 29 29 30 31 33 33 34 35 36 37 38 38 Installing the Appliance . . 45. 7 cm appliances - freezer appliances with/without water dispensing . 45. 7 cm appliances - wine storage compartment 61 cm appliances - refrigerated and freezer appliances with/without ice and water dispenser . [. . . ] A ventilation grille is enclosed with the appliance for the changed door stop position. In further mounting the appliance, use this part. D Remove the hinge covering. D Swap the hinge angle to the other side. 18 D D D Screw the door to the hinges. Fit in the plastic part of the new ventilation grille. In addition, set the screw from I to 0. D Attach the hinges to the appliance. D Exchange the hinges crosswise! D Attach the hinge covers. 19 6. Note: Preparing the installation niche Subsurface wooden floors The wood screws (5 x 60 mm and 4 x 15 mm) which are supplied should be used for wooden floors. D For each appliance, two anti tilt ribs are needed. In the case of a side by side combination, a total of two anti tilt ribs are used. D Drilling guide holes: 3 mm for the wood screws (5 x 60 mm) 2 mm for the wood screws (4 x 15 mm) Ensure that the screws 5 x 60 at least take a hold (19 mm) in the solid subsurface. Determine the fastening points of the anti tilt ribs. Determine the actual dimensions according to the section Installation Dimensions". ! D Caution! Tightly screw the anti tilt ribs. Re examine to make sure that the screws are firmly tightened! Ensure that in the wall area there are no electrical wires or pipes which could be damaged by pipes. Risk of injury or damage! D If a installation niche is deeper than the appliance, lay a strong wooden plank behind the anti tilt ribs and screw tightly to the subsurface or the wall. The length of the plank should correspond to the width of the installation niche!Subsurface concrete ! Important note: As far as possible, always screw the wooden plank to the rear wall of the niche. In the case of some fitted shapes, it may be necessary to screw in at an angle the wood screws used to fasten the anti tilt ribs to the rear wall. Important information for securing against tilting: The set supplied, contains fastening screws for various subsurfaces. If it is not possible to securely fasten the anti tilt ribs and consequently, not possible to securely fasten the appliance using the fastening screws supplied, select another suitable method for securely fastening the anti tilt ribs. Warning! When installing or working with floor anchors, always wear protective glasses or other protective equipment / clothing. Floor anchors are not suitable for use in connection with lightweight construction masonry, breeze blocks or tiles. In addition, use the wood screws supplied (5 x 60 mm and 4 x 15 mm). D - Drill a hole with a 10 mm diameter having a depth a little more than the raising depth. Use the drill supplied. 20 D Clean the hole or drill a little deeper. Note: If the installation niche is deeper than the appliance, select a stronger beam or use two, one behind the other. The plank must overlap the appliance by at least 50 mm. - D By hand, screw into the dowel until you can feel resistance. Strike the dowel and screw into the hole until the head of the screw has a 13 mm distance to the anti tilt securing device. Screw tightly. D D D Mark the installation height (underside edge of the plank) on the rear wall of the niche. Select the screws according to the thickness of the wooden plank: Length min. 2. 5 x wood thickness, diameter 12 or 14 mm. D Note: Select the number of screws corresponding to the niche width so that you ensure that the plank can be securely mounted. According to the subsurface: D D Additionally use the supplied wood screws (if the subsurface allows). 7. Attaching an additional anti tilt mechanism Important note: As far as possible, always screw the wooden plank to the rear wall of the niche. If the anti tilt ribs cannot be fastened securely, a wooden beam can be used above the appliance as an alternative anti tilt mechanism. [. . . ] Clamp the finger protection to the fastening clips (2. ). D Pull the finger protection up to the hinge side of the door. The sections on the finger protection have to be exactly aligned to the height of the fastening clips. D Clamp the holding clips under the screws. Screw tightly. D Transfer the door dimensions (upper/below) to the finger protection. Shorten the finger protection using a steel rule and a knife to the required length. D 33 25. [. . . ]