User manual AUDIOVOX AOM-7694

[. . . ] ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY SHALL , BE LIMITED TO THE DURATION OF THIS WARRANTY ANY ACTION FOR BREECH . OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 DAYS FROM THE DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREECH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the company any liability other that expressed herein in connection with the sale of this product. [. . . ] Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. ELKHART, IN 46514 Visit us at http://www. asaelectronics. com UDIOVOX PECIALIZED 5" MONOCHROME OBSERVATION AOM-7694 Features: 5" Monochrome Monitor Dual Camera Input Brightness/Contrast/Day-Night Controls Volume Control for Internal/ External Speaker Power/Stand by Button Front Panel Controls Back Lit AOM-7694 POWER INPUT DAY/NIGHT + + + e1 PPLICATIONS, L. L. C. 022352 FEATURES : AOM-7694 Monochrome 5" Monitor Day/night switch Brightness and contrast controls Volume control Illuminated front panel Power/stand-by switch Internal speaker with external speaker jack IMPORTANT : Congratulations on your purchase of a Voyager AOM-7694 monitor. With proper installation and use, your AOM-7694 is designed to provide you with years of trouble-free operation. This manual contains important information required to properly install and operate the unit. All Voyager Observation products are strictly intended to be installed as a supplement aid to standard rear-mirror systems that may already exist in your vehicle. Voyager observation products are not intended for use as substitutes for rear-view mirror devices, or for any other standard motor vehicle equipment required to be installed on vehicles by law. While Voyager observation products contribute to improving the vehicle operator's field of view, these products are no substitute for proper defensive driving techniques and observance of traffic laws and motor vehicle safety regulations. CONTENTS : AOM-7694 5" Monochrome Monitor : 1 - 5" monitor 1 - Snap-on sun visor 1 - Monitor bracket 1 - Power harness with locking connector 1 - Range markers 4 - Thumb screws (M5 x15) with plain washer & spring washers 4 - Attachment screws with washers (M5 x12) Documents: 1 - Operations manual 1 2 CONTROLS AND OPERATION Monitor 1. BY - Monitor operates when vehicle transmission is switched into " REVERSE ". To increase protection of cable, place all excess wire and extension cable in convoluted tubing. Do not twist camera cable and do not cut camera pigtail or cable. 110. 0 ** WARNING ** 1. If evidence of tampering is detected, the warranty will be considered void. Use the thumbscrews to mount the monitor to bracket. MONITOR MOUNTING HOLE PATTERN DASHBOARD OR OVERHEAD 5 6 FIGURE 1 FIGURE 2 5. 275 6. 240 2. 677 2. 250 BEFORE INSTALLATION : 1. This system operates from 11 volts DC to 30 volts DC, negative ground. Please install this system according to the instructions in this manual. Connection to a battery source will reduce battery life. 20 20 WIRING CAMERA AND MONITOR 1. See wiring diagram for connections to ignition, ground and back-up circuit (See Fig. Wiring Camera : Drill a 19 mm / " diameter hole into vehicle body near the camera and bracket. [. . . ] Wiring Camera : Drill a 19 mm / " diameter hole into vehicle body near the camera and bracket. Push extra cable into vehicle (Be careful not to kink cable) and fit grommet into hole. Apply sealant around grommet to increase resistance to water penetration. Wiring Monitor : Insert extension cable into camera #1 position if (2) camera are used, be sure to mark each extension cable property and plug second cable into camera #2 position. [. . . ]