User manual AUDIOLINE TEL2

[. . . ] TEL2 Slim Line Phone User guide Downloaded from: http://www. guardianalarms. net FUNCTIONS 1 2 3 4 5 Loudspeaker Hook switch Memory buttons (M1-M3) Recall button Memory button 6 7 8 9 Volume controls Redial button Store/Mute button & indicator Digit buttons (0-9, *, # ) CONNECTING # # Connect the line cord to the wall socket. Lift the handset and check for dial tone. WALL MOUNTING The Audioline TEL2 can be wall mounted directly onto the standard wall plate or to the wall using the template (provided) and suitable screws (not provided). When wall mounting you will need to rotate the handset retaining clip (located on the cradle) 180 degrees to ensure the handset remains on the cradle. TO CALL # Lift the handset and wait for dial tone. [. . . ] Store a indirect memory: # Lift the handset # Press the [STORE] button (ignore network tones) # Press the [MEMORY] button (item 5 on diagram) # Select memory location (0-9) # Enter the phone number (max 21 digits) # Press the [STORE] button # Replace the handset or press the hook switch (item 2 on diagram) Dialling with indirect memory: # Lift the handset and wait for signal. If you want to change a number, enter the new number and the old will be replaced. If you wish to insert a pause (3 seconds) into the dialling sequence, press the [REDIAL] button (item 7 on diagram). ADJUSTABLE RINGER This telephone has programmable ringer selection. You can select between three levels of three types of ring signal plus ringer off. P Lift the handset (ignore network tones) # Press [STORE/MUTE] button P Press [#] button P Select required ring signal by pressing buttons 0 - 9 as per table below. P Replace the handset, the ring signal is now selected Key/setting 1 2 3 4 5 6 (default setting) 7 8 9 0 Melody type Melody A Melody A Melody A Melody B Melody B Melody B Melody C Melody C Melody C Off * Ringer level Low Normal High Low Normal High Low Normal High - * If setting 0 is selected, the ring signal will be turned off until the handset is lifted again. After that, the ring signal reverts to the previous setting. RECALL The [RECALL] button can be used to access additional Network services and PBX functions. The Audioline TEL2 is pre-set to 100ms Time Break Recall for Australia and 600ms for New Zealand. TROUBLESHOOTING NO DIAL TONE Try the phone in a known good socket to establish whether the fault is with the phone or the line. PHONE DOES NOT RING Lift and replace the handset and reset the ringer to the previous setting. MEMORY NUMBERS NOT DIALLING CORRECTLY Repeat the memory storage procedure and retry. WARNING It is recommended that you disconnect your telephone during a thunderstorm as you can get a shock from your telephone (and other electrical appliances). We recommend you follow these simple precautions during a thunderstorm: # Do not use your telephone unless the call is urgent. # If you must use your telephone, make the call as brief as possible and keep clear of electrical equipment and metal fixtures. # Do not touch brick or concrete walls. NOTE: Do not install your telephone in damp or high humidity locations, such as a laundry or bathroom. If any damage is caused by such elements it is not covered by the manufacturers warranty. CLEANING The casing should be cleaned by wiping with a damp cloth. # Do not use abrasives, solvents or spray polish that may enter through holes in the earpiece and mouthpiece and cause damage. # Do not place the telephone in direct sunlight or use in extreme humidity. REN (RN for New Zealand) The REN (Ringer Equivalance Number) or RN is of significance only if you wish to connect more than 1 telephone to your telephone line. [. . . ] Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment o f a different make or model, nor does it imply that any product is compatible with all of Telecom's network services. This equipment shall not be set to make automatic calls to the Telecom "111" Emergency Service. This Equipment may not provide for the effective hand-over of a call to another device connected to the same line . [. . . ]