User manual AUDIOLINE SENSOR 500

[. . . ] 14 Call Answering. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Miscellaneous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Trouble shooting. . . . . . . . . . . . . . . . . . . . 17 Guarantee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2 LOCATION OF CONTROLS 1 2 3 4 5 6 7 8 9 10 11 12 13 3 Handset Curly cord socket Wall mounting hook Hook switch Dial-Up key Scroll call list/phonebook, replay Line cord socket (rear) Display Message waiting indicator Play/Pause messages Headset socket (rear) Switch between speaker/headset Switch for ringer level 14 15 16 17 18 19 20 21 22 23 24 25 Erase key Scroll call list/phonebook, save Speed-dial/pre-programmed keys Volume control for handset Volume control for speaker Mute key Key/indicator for speaker/headset Dial keys 0-9, *, # Programming key Redial key Recall-key Phonebook access CONNECTION TO THE TELEPHONE NETWORK · Connect the curly cord to the left-hand side of the telephone and to the bottom of the handset. · Connet the power cord to middle socket of telephone and plug into power outlet. · Connect the telephone line cord to the socket entitled "LINE" on the rear of the telephone and then connect the cord to the network wall outlet. [. . . ] Ensure that the switch on the right hand side of the phone is set to . Use the volume control on the right hand side to adjust the sound level. · To terminate the call replace the handset. USING a HEADSET 1. · Press and release to terminate the call. 7 LAST NUMBER REDIAL If the last number dialled was engaged or the call was not answered, it is possible to redial the number using the button. The telephone number will be dialled automatically. · When the called party answers, lift the handset (or headset) to converse. If the call is not answered, press and release It's also possible to lift the handset and then press the redial key. VOLUME CONTROL The sound volume in the handset or headset can be adjusted using the [VOL ] to increase the volume , and [VOL ] to decrease the volume. MUTE If during a telephone conversation, you wish to talk privately to a third party without the caller overhearing: Press the button (the word MUTE will appear on the display). To resume the conversation, press the button again. PAUSE A short pause to numbers stored in the phone book and the speed-dial memories, using this button. This may be required if the phone is connected to a PABX or if used with some network services. TELEPHONE RINGER The telephone ringer volume can be set to either high, low or off which is represented by this symbol . 8 CALLER DISPLAY Caller display allows you to see who is calling before you answer a call and to see who has called in your absense. When the service is implemented on your telephone line, seconds before your telephone rings the number of the incomming caller will appear on the display. When the list is full, the oldest number will be deleted automatically. It is not possible to view the call list and take a new call at the same time. If the caller Display service is not implemented on your telephone line, incomming call information will not be displayed. NEW NUMBERS The words NEW CALL and the number of calls will appear on the display. Once the number(s) have been reviewed, NEW CALL will disappear and the indicator will stop flashing. When an incoming number is received it is assigned a call sequence number which appears on the top left hand side of the display, commencing with 01 (oldest call) up to 60 (latest call). 9 REVIEWING PHONE NUMBER Scroll the memory with the keys or . If the number is stored iin the phonebook the corresponding name is also shown. 9 - 2805000 LIST INFORMATION The display will also provide the following information: 17 10 :56 14/10 Phone number 9-2805000, received at 10:56 the 14th October. Position number 17. 10 ERASE PHONE NUMBER(S) You may erase a single number or all numbers on the call list. ERASE A NUMBER · Scroll the call list until the number to be erased is shown on the display. · Press C twice quickly, then release ERASE ALL NUMBERS · Scroll the call list until a number is shown on the display. · Press and hold C until the display shows "ERASE ALL?". , then release. All phone numbers are now erased. IF THE CALL LIST IS FULL The call list memory capacity is 60 telephone numbers. When the memory is full, each new coming call will replace the oldest stored number, the principle "first in' first out" applies. The new number receives the highest number, 60, and all other numbers are moved one step up in the memory order. DIALLING A NUMBER FROM THE CALL LIST · Scroll the call list with displayed. and then lift the handset when · Lift the handset and press and release It is also possible to first press and release the called party answers. NOTE! If a charge for local calls is unacceptable, the "Dial Button" should not be used for local calls when using some Service providers. [. . . ] You should not exceed a value of 5 on the complete system, otherwise the volume of the ringer in any phone will decrease and one telephone may not ring at all. 17 GUARANTEE If you believe your SENSOR 500 is malfunctioning, please refer to the relevant section and/or consult the troubleshooting guide in this manual to ensure that you have followed the instructions carefully. The SENSOR 500 is warranted for a period of 12 months from the date of purchase by you, the end user. If the product is then found to be faulty you will be asked to return it directly to the service agent, ATLAS GENTECH (NZ) LIMITED with a copy of the purchase receipt. ATLAS GENTECH (NZ) LIMITED 87 Carbine Road, Mt Wellington, Auckland Service & Spare Parts (Toll Call): 0900 50 025 Fax: (09) 574-2722 Email: helpdesk@atlasgentech. co. nz NOTE: The guarantee does not extend to damage caused by misuse, negligence, excessive voltage, faults on the telephone line or lighting. [. . . ]