User manual AUDIOLINE DECT 4800

[. . . ] - User controls - 2 User controls 1 1. 2 12 11 3 4 5 Call indicator, flashes for newly recorded messages 2. 4. Call indicator Answering machine on/ Message indicator Charge monitoring lamp Paging button. 4 66 - Setting up - 3 3. 1 Safety Information Setting up NOTE Before setting-up, it is essential that you read the General Information at the beginning of this manual. 3. 2 The following items are supplied: one base station one handset with belt clip one telephone connecting cable Check contents of pack one mains power supply two standard batteries one instruction manual 3. 3 Connecting the base station Position the base station near to your telephone connection socket and to a mains socket. 1. 2. 3. Insert the plug of the power supply into the socket on the rear of the base station and plug the power supply into a properly installed 230 V mains socket. The plug-in power supply for the base station must always be connected. [. . . ] 3x Display FEATURES DISPLAY LANGUAGE GERMAN or ENGLISH Select GERMAN or ENGLISH 92 - Special functions 8. 10 Changing the call duration display The actual duration of the call will appear in the display while a call is being made. 3x DISPLAY LANGUAGE 2x CALL TIMER ON or OFF Select ON or OFF CALL TIMER Press and hold button You can determine whether the duration of the call is displayed or not. Button Display FEATURES 8. 11 Changing the PIN code on the base station Button Display FEATURES 4x SYSTEM REGISTER 3x Number pad Number pad Number pad CHANGE PIN PIN?CHANGE PIN Press and hold button Some functions of the telephone system are protected against unauthorised use by a PIN code. As supplied, the PIN code is set to "0000". 93 - Special functions 8. 12 Deleting all lists Button Display FEATURES RESET RECORDS RESET?Press and hold button The contents of the phone book, the redial facility and the caller list can be deleted with one procedure. 5x 8. 13 Factory settings Button Display FEATURES 5x RESET RESET 1x Number pad SETTINGS PIN?Enter the PIN code for the base station SETTINGS The factory settings are reset. External ring melody tone 1 Internal ring melody tone 2 Basis ring melody 1 Handset ringer volume 3 Base station ringer volume 3 Direct dialling off PIN 0 0 0 0 Call accept 5 rings Record calls Message tone off Receiver volume medium Flash time 1 Confirmation tone on Tone dialling Language: German Baby call off Answering machine on Standard greeting on Recording time 2 min. SOS Code 111 Button click on Automatic call accept on Call duration on Charging monitor on Monitor off Dialling blocks off Listen-in on Exception numbers off Blocks off PIN remote access 000 You can reset the handset to the factory settings once more by means of the Factory Settings function. 94 - The answering machine - 9 The answering machine The integral answering machine can digitally store up to 25 incoming messages with a total length of up to 9 minutes. For your greeting message, you can use two pre-recorded standard messages or you can record two messages of your own. If you have not recorded your own greeting, the standard greeting will answer automatically. Note: Even when the answering machine has already accepted the call, you can also accept the call by means of the call button . In this case, the recording of the message will be automatically terminated. Press 1 to switch on the answering machine control. 876 9 10 11 12 5 4 3 2 1 1. Start answering machine control Changeover greeting mode Record greeting Play back greeting Skip messages Switch answering machine on/off 7. Play back messages Stop button Repeat messages Play back memo Record memo Delete messages When the answering machine control is switched on, the display will change back to the normal display after ca. 30 seconds if no entries are made. 95 - The answering machine 9. 1 To switch the answering machine on, proceed as follows: Button Display Switching the answering machine on/off ANS RECORD, ANS ONLY or AM OFF Comment The messages ANS RECORD, ANS ONLY or AM OFF will appear in the display Switching on or off takes ca. Hold button pressed to return to main display. When the answering machine is switched on, the symbol appears in the indicator light on the base station comes on. display and the 9. 2 9. 2. 1 Maximum recording time General settings Button Display FEATURES 6x ANSWER MAC RING DELAY 2x MSG LENGTH 1 MINUTE or 2 MINUTES Select the required length. MSG LENGTH Press and hold button The integral answering machine can digitally store up to 9 minutes of incoming messages. If the caller speaks for longer, a signal tone sounds and the call will be cut off. [. . . ] When selecting and then select the required base FIXED, confirm with station by means of the number pad. If the handset is logged on to different base stations, the appropriate numbers will flash. SELECT BS 4x 113 - Troubleshooting - 11 Troubleshooting If you have problems with your telephone, please check the following points first. No calls possible o The telephone line is not correctly connected or is faulty. [. . . ]