User manual AT&T 9002

[. . . ] Even if you have dial pulse service, you can still use telephone services requiring tone signals. See "Temporary Tone" in the OPERATION section of this manual. 2 3 3 9002_book. 1AT&T 3 8/12/98, 4:09 PM INSTALLATION 4 Connect the telephone line cord(s) to the base. · If you have two separate jacks, use both the white and clear line cords. Insert one end of the white line cord into the jack labeled L1/L2 on the back of the base. [. . . ] 2 When you hear a dial tone, press R. Handset Ringer Selection and Ringer OFF You can select from four different handset ringer styles for each line. You will hear a sample of the ringer style -- OR -- Press 0 to turn the ringer off. 4 Press p. 9 9002_book. 1AT&T 9 8/12/98, 4:09 PM OPERATION Checking Handset Ringer Selection 1 2 3 4 Press p, *. Press o to exit. NOTE: If you're on a call on one line and a call comes in on the other line, you will hear an "alert" tone on your call. Handset Ringer Volume Adjust the handset ringer volume to high (H) or low (L) using the switch on the side of the handset. Base Ringer Volume Line 1 and Line 2 ringers on the base have been assigned different ringing styles. You can adjust the volume of the base ringers to HIGH, LOW or OFF using the switches on the side of the base. Speakerphone Volume Use + and - on the base to adjust the volume of the speakerphone. Temporary Tone NOTE: If you have touch tone service, you do not need to use the Temporary Tone feature. If you have dial pulse (rotary) service, this feature allows you to enter codes or tones needed to operate answering machines, or use electronic banking services, calling cards, and other special services. This feature will operate most special services; however, some services may actually require a touch tone line. 2 After you hang up, the phone automatically returns to dial pulse (rotary) dialing. 10 9002_book. 1AT&T 10 8/12/98, 4:09 PM OPERATION Special Telephone Services If you subscribe to special local telephone company services like Call Waiting or Call Forwarding, you can access them by pressing the line button of the line you're currently using whenever you would press the switchhook on a corded phone. This is like the Flash feature on some other phones. Hold 1 2 Press H on the base or the handset to put a call on hold. The light for the line you've put on hold flashes on the handset and on the base. Press the appropriate line button, on either the handset or the base, to return to your call. Mute (Base Only) Mute allows you to hear your caller, but prevents the caller from hearing you. This can be helpful if you are using the base speakerphone in a noisy location. 2 To return to your conversation, press M again. Page The Page feature allows you to signal someone at the handset from the base. The person at the handset can then press I on the handset to open the intercom connection, or press o to stop the ringing before it stops automatically. Intercom 1 Press I on the handset. The person at the base only needs to speak toward the base to answer the handset. To close the intercom connection, press o on either the handset or the base. 2 11 9002_book. 1AT&T 11 8/12/98, 4:09 PM OPERATION Conference Calls You can use both lines at the same time to set up a three-way conference call from the handset. If you receive a call while you are out of range, the handset might not ring -- or if it does ring, the call might not connect when you press the line button. If you move out of range during a phone conversation, you will hear noise or interference. If you move out of range without pressing o, your phone will be left "off the hook. " To hang up properly, walk back into range, periodically pressing o. This cordless telephone has 10 channels available for maximum performance. If you notice noise or interference while using the handset: 1 Press c. 2 If the interference doesn't clear, continue to press c until you find a clear channel -- OR -- Move closer to the base and press c. 14 9002_book. 1AT&T 14 8/12/98, 4:09 PM TELEPHONE MEMORY This cordless phone can store 10 telephone numbers that you can dial just by pressing p and a number button. Storing Memory Numbers 1 2 3 4 Make sure the handset is off. [. . . ] The layout of your home or office might be limiting the operating range. Try moving the base to another location, preferably on an upper floor. · · 18 9002_book. 1AT&T 18 8/12/98, 4:09 PM IN CASE OF DIFFICULTY If the phone does not ring when you receive a call: · · · · · · Make sure the handset ringer is on. Make sure the telephone line cord(s) is connected firmly to the base and the modular telephone jack(s). Make sure the AC adapter is plugged firmly into an outlet not controlled by a wall switch. [. . . ]