User manual AT&T 6200

[. . . ] Attach the belt clip to the cordless handset as in Figure B below (optional). a) Remove battery compartment cover by pressing on the indentation and sliding downward. b) Align two holes in plug with socket pins, and snap the plug into place. To attach c) Place battery pack in compartment with the wires in the lower left corner, along the bottom of the battery pack. d) Replace cover by sliding it up into place. Figure A Figure B To remove Table/Desk Installation 3 Charge the handset battery. After the first charge, the battery is typically fully charged overnight. After the batteries are charged, pick up the handset and press P; you should hear a dial tone. Standard electrical outlet Modular telephone jack 4 1 Connect the telephone line cord. 2 Connect the power cord. 2 INSTALLATION Wall Installation 1 2 3 4 5 Position the wall mount adapter on the base. Follow Steps 3 and 4 in Table/Desk Installation. Align tabs on wall mount adapter with holes on bottom of base. [. . . ] If you move out of range without pressing P, your phone will be left "off the hook. " To hang up properly, walk back into range, periodically pressing P. TELEPHONE MEMORY This cordless phone can store nine telephone numbers, each up to 16 digits long. Store Memory Numbers 1 Make sure the handset is off. 3 Dial the telephone number (up to 16 digits) -- OR -- Press R to store the last number dialed. 5 Press the number button (1­9) where you want to store the telephone number. Change/Replace a Stored Memory Number Store a new number in its place. Store a Pause in a Memory Number Press to store a two-second pause in the dialing sequence. Each press adds another two-second pause and counts as one digit. Directory Label Use the self-adhesive directory label to keep a record of the numbers (or names) stored in memory. It's best to write on the label before applying it to the phone. Dial Memory Numbers 1 Press P or . 2 Press and release g, then press the number button (1­9) where the memory number is stored. 6 BATTERIES Charging the Handset Battery Pack This battery should remain charged up to six days with the ringer turned on and up to 12 days with the ringer off. A fully charged battery provides an average talk time of about six hours. The battery pack needs charging when: · A new battery is installed in the handset. You can keep the battery fully charged by returning the handset to the base after each use. If you repeatedly get a low battery indicator, even after eight hours of charging, the battery should be replaced. Replacing the Handset Battery Pack 1 Remove the battery compartment cover on the handset by pressing on the indentation and sliding the cover downward. Align the two holes in the new battery pack's plug with the socket pins, and snap the plug into place. Place the battery pack in the compartment with the wires in the lower left corner, along the bottom of the battery pack. Place the handset in the base and allow it to charge for at least 24 hours the first charge. The telephone might operate before that, but for best performance, let the battery pack charge fully. 2 3 4 5 7 IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions below. For Customer Service, visit our website at www. telephones. att. com or call 1 800 222­3111. Please retain your receipt as your proof of purchase. If you hear noise or interference when using the phone: · · · Make sure the base antenna is fully upright. Press and release C to change to another of the 30 channels available. If noise is exceptionally loud, move closer to the base before changing channels. [. . . ] Put the handset in the base to re-initialize. If you hear other calls while using your phone: · · If you lose a call after changing channels: You were probably almost out of range. Before placing another call, set the handset in the base for at least 15 seconds. If you hear a two-beep signal when you try to use the handset: · · You might be out of range. If moving closer to the base doesn't help, try following the directions above for re-initializing the handset and base. If you need to change your Personal Identification Number (PIN) or Account Number: Instructions for changing your PIN or Account Number are available by calling Net2Phone Customer Service at 1 877 N2Phone (1 877 627-4663). If the phone does not ring when you receive a call: · · · · · Make sure the handset ringer is on. Make sure the telephone line cord is connected firmly to the base and the telephone jack. [. . . ]