User manual AT&T 1412

[. . . ] 1412 2002. 12. 7 9:20 AM Page II USER'S MANUAL Part 2 2. 4 GHz Two-Line Cordless Speakerphone 1412 with Caller ID/Call Waiting on Handset Please also read Part 1 -- Important Product Information © 2002 Advanced American Telephones. AT&T and the Globe Symbol are trademarks of AT&TCorp. , licensed to Advanced American Telephones. 1412 2002. 12. 7 9:20 AM Page III Visit us at www. telephones. att. com © 2002 Advanced American Telephones. AT&T and the Globe Design are trademarks of AT&T Corp. , licensed to Advanced American Telephones. Issue 1AT&T 12/02 1412updatedmanual 2002. 12. 7 9:20 AM Page IV CONTENTS BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . [. . . ] When the second call is established press to connect both far end parties to the conversation. use 29 1412 2002. 12. 7 9:20 AM Page 30 Four-Way Conference Call You can connect four parties to a conversation using Lines 1 and 2, the handset and the base. 2 Once all three parties are connected, the fourth party can press either button at the base or handset not already connected to the call. All four parties will now be able to hear each other. End a Conference Call To release one of the outside parties from a conference call, press for the party you wish to keep connected. To release the entire conference call, press the buttons on the base and/or handset connected to the call twice. 30 1412 2002. 12. 7 9:20 AM Page 31 Place a Conference Call on Hold While on a conference call, press on the handset or base. To return to the conference call, press at the base, or press on the handset when the screen shows the conference menu. Speak Privately with One Party You can speak with one party in a conference call without disconnecting the other parties. To return to the conference call with all parties, press at the base -- OR -- Press or on the handset until the conference menu appears on screen;then press . 31 1412 2002. 12. 7 9:20 AM Page 32 Switch a Conference Call Between Handset and Base If you place a conference call from one location, you can switch it to the other location without disconnecting the call. Switch from Handset to Base 1 2 At the handset, press . Now, the call is connected at the base and automatically disconnected at the handset. Press or at the handset until the conference menu appears on screen;then press . Now, the call is connected at the handset and automatically disconnected at the base. Switch from Base to Handset 1 2 3 32 1412 2002. 12. 7 9:20 AM Page 33 DIRECTORY This handset can store up to 50 telephone numbers and names. Each number can be up to 24 digits long and each name can be up to 15 characters long. Entries are stored alphabetically ¥NOTE: You can exit the Directory at any time by pressing again. Store a Number and Name in the Directory 1 From the idle screen, press displays . The screen AM 2 (If the directory is empty, the screen displays and then the screen above. ) Press . The screen displays AM 3 Use the keypad to enter the number you want to store. To enter a pause in the dialing sequence, press and hold the digit just before you want the phone to pause when dialing. AM 33 1412 2002. 12. 7 9:20 AM Page 34 4 Press when you finish entering the number. The screen displays AM NOTE: include ¥number. Every directory entry mustentering a If you press without a number, the screen will not change and you will not be able to enter a name. The screen displays AM 6 To add a space or move to the next position, press . The screen displays , then AM Every ¥NOTE: If you directory entry must include a name. press without entering a name, the screen will not change and you will not be able to complete the directory entry. If you want the phone to alert you with a special ring when you receive an incoming call with Caller ID information from this number, set this directory entry to . Press or 8 34 1412 2002. 12. 7 9:20 AM Page 35 Store a Number from Handset Redial in the Directory 1 2 3 Press . Use or to scroll through the number s stored in the handset redial memory. [. . . ] Connect the power to the base. PROBLEM If you hear noise or interference when using the phone: SOLUTION · You may be out of range. If noise is exceptionally loud, move closer to the base before changing channels. · Household appliances plugged into the same circuit as the base can sometimes cause interference. · The layout of your home or office may be limiting the operating range. [. . . ]