User manual ALPINE VPA-B222R

[. . . ] FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE/PARA USO EN AUTOMÓVILES/SOLO PER L'UTILIZZO IN AUTOMOBILE/ENDAST FÖR BILBRUK R Vehiclehub Pro EN VPA-B222R DE · OWNER'S MANUAL Please read before using this equipment. · BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes. · MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. [. . . ] · For linear PCM signals, the voice is output from the rear speaker regardless of the REAR FILL and REAR MIX setting. 37-EN Achieving powerful high volume sound With Dolby Digital, the dynamic range is compressed so that powerful sound can be achieved at regular volume levels. This compression can be cancelled to achieve an energetic sound with even greater power, like the sound in a movie theater. This function works only in the Dolby Digital mode. Press the joystick left or right to select STD or MAX. STD: For powerful sound at regular volume levels MAX. : For powerful sound at high volumes Adjusting the DVD Level The volume (signal level) for Dolby Digital, Dolby PL II, DTS and PCM modes can be set. · Avoid stopping, pausing, switching the disc, cueing, fast-forwarding or switching the audio channel of this unit while making this adjustment. The setting is cancelled if the Decode mode is switched. 1 2 3 4 5 6 7 Check that Defeat mode is off (page 12). Press and hold TA/RTN/SETUP for at least 2 seconds. The SETUP screen is displayed. · Keep the volume to a level at which sounds outside the vehicle can still be heard. Adjusting the speaker levels The test tones help to make the volume adjustments of the different speakers. When levels are equal, a strong sense of presence can be heard from the different speakers at the listening position. · Avoid stopping, pausing, switching the disc, cueing, fast-forwarding or switching the audio channel of this unit while making this adjustment. Test tone output is repeated for each of the different speaker channels. If no operation is performed for 2 seconds, the channel switches to the next channel. Left Centre Left surround Right Left Right Surround Press the joystick up or down to select AP SETUP, then press the joystick right. The AP SETUP screen is displayed. Press the joystick up or down to select DVD LEVEL, then press the joystick right. The DVD LEVEL screen is displayed. Press the joystick up or down to select the desired mode. Press the joystick left or right to adjust level. The level can be adjusted in the range of ­5 to +5. Repeat step 5 and 6 to set each level. Storing Settings in the Memory Adjustment or setting contents can be stored. Contents that can be stored vary depends on the audio processor used. 2 Press the joystick down to select OUTPUT LEVEL. 3 Press the joystick left or right to balance the output from all the speakers. · The adjustment range for the different speakers is ­10 dB - +10 dB. · If a speaker is set to off mode, that speaker's level adjustment cannot be made. Refer to "Speaker Setup" (page 36). 1 2 3 4 5 Check that Defeat mode is off (page 12). Press and hold TA/RTN/SETUP for at least 2 seconds. The SETUP screen is displayed. Press the joystick up or down to select AP SETUP, then press the joystick right. The AP SETUP screen is displayed. Press the joystick up or down to select PRESET MEMORY, then press the joystick right. Press the joystick up or down to select any one of the preset numbers (1 through 6), then press // ENTER. The setting contents are stored. · The stored contents will not be deleted even when the battery power cord is detached. 38-EN Calling up the Preset Memory 1 2 3 4 5 Check that Defeat mode is off (page 12). Press and hold TA/RTN/SETUP for at least 2 seconds. The SETUP screen is displayed. If MUSIC is selected, the centre width can be adjusted with the following operations. This function offers the optimum vocal position by adjusting the centre channel position between the centre speaker and the L/R speaker (The adjustments established in "Adjusting the acoustic image" (page 37) are ineffective while this function is activated). Press the joystick up or down to select AP SETUP, then press the joystick right. The AP SETUP screen is displayed. 1 Press the joystick down to select CENTER WIDTH, then press the joystick left or right to select ON. When the level increases, the centre channel position moves from the centre speaker position to both sides. [. . . ] Tryck på SOURCE/POWER efter att du lagt på och avsluta telefonens avbrott. Även om skärmbilden för källan visas matas inget ljud ut. - 1) Se till att fjärrkontrollen blinkar snabbt och lägg på luren. - När högtalaringångens läge (FACT SYS SET) är inställt på INT eller BOTH, eller om typen av röstavbrott (F. SYS MIX TYP) är inställd på MUTE, kommer telefonen att avbryta om bilsystemets ljud sätts på i en annan källa än FACTORY SYS. [. . . ]