User manual AEG-ELECTROLUX HV2730BEN
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG-ELECTROLUX HV2730BEN. We hope that this AEG-ELECTROLUX HV2730BEN user guide will be useful to you.
Manual abstract: user guide AEG-ELECTROLUX HV2730BEN
Detailed instructions for use are in the User's Guide.
[. . . ] 11. Children should not be left alone or unattended in the area where this appliance is in use. Always turn hood ON when cooking at high heat or when cooking flaming foods. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWINGa:
WARNING
A. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. [. . . ] Lay out and cut the cooktop cut-out far enough FORWARD so downdraft will fit behind it. Center and square it with edges of countertop.
· ·
the position of the blower discharge needs to be moved so ductwork does not interfere with floor joists, plumbing or wiring below. it is necessary to rotate the blower discharge to the RIGHT or LEFT.
Place the unit on its back on a table or work surface.
DOWN DISCHARGE - MOVING BLOWER LEFT OR RIGHT
BLOWER NUTS CLAMP CHANNEL SHEET METAL SCREW
3. Place the plastic template against the back flange of the cooktop and center it. Tighten nuts to secure top of blower and use sheet metal screws through bottom flange to secure bottom of blower.
BOTTOM FLANGE
5. Be careful not to chip edges of countertop.
MOUNT THE UNIT
MOUNTING SCREWS LEVELING BRACKET FLANGE FACING OUT
LEFT OR RIGHT DISCHARGE
BLOWER NUT
CLAMP CHANNEL
MOTOR PLUG SHEET METAL SCREW
LEVELING BRACKET FLANGE FACING IN
COVER PLATE
1. Replace clamp channels and use nuts to secure the blower in its new position. Use sheet metal screws through bottom flange to secure bottom of blower.
1. Extend leveling brackets to floor of cabinet so downdraft sits straight. (Note: Leveling brackets can be removed and re-attached in other positions. Bottom flange may have to face inward in tight cabinet installations. ) 2. Secure the downdraft to the countertop as follows: Hold the downdraft against the back of countertop cut-out and tightening the 2 mounting screws (one on each end of unit) on underside of countertop. Use a wood shim between screw and underside of granite countertops.
3
3. Tighten screws holding leveling bracket to unit on each side.
INSTALL DUCTWORK
CAUTION - BEFORE CUTTING HOLE IN CABINET FOR DUCTWORK: Check for interference with floor joists, wall studs, electrical wiring or plumbing.
WIRING DIAGRAM
ç BLOWER
è
3-1/4" X 10" TO 6" RD. Note: Accurate alignment of cooktop and downdraft is necessary to ensure that there is no interference when air vent is raised and lowered. There should be a gap of 1/32"-1/16" between the back of the cooktop and the front of the downdraft cover.
1. Mount the roof or wall cap and work back towards the cabinet, attaching all ductwork, elbows and transitions as previously planned. If necessary, LOOSEN nuts and screws that hold the blower in place, and slide blower left or right to meet ductwork. Note: A 3-1/4" x 10" collar is provided for installers who prefer to rivet the ductwork to the unit. This will allow blower to be removed and replaced easily in service situations without disturbing ductwork.
ADJUSTMENT
The downdraft is factory-adjusted for proper operation. However, shipping and handling may affect the position of the activating switch. To adjust position of activating switch:
WARNING: To avoid possible electrical shock, personal injury or death Disconnect electrical power.
1. [. . . ] Damages caused by services performed by persons other than authorized Frigidaire servicers; use of parts other than Frigidaire Home Products Genuine Renewal Parts; obtained from persons other than such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God. Products with original serial numbers that have been removed or altered and cannot be readily determined. Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty period should service be required. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX HV2730BEN
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX HV2730BEN will begin.