User manual AEG-ELECTROLUX F55020WOP

[. . . ] FAVORIT 55020 DISHWASHER USER MANUAL 2 CONTENTS 4 6 7 8 9 10 13 16 17 20 21 SAFETY INFORMATION PRODUCT DESCRIPTION CONTROL PANEL PROGRAMMES OPTIONS BEFORE FIRST USE DAILY USE CARE AND CLEANING TROUBLESHOOTING INSTALLATION TECHNICAL INFORMATION ENVIRONMENT CONCERNS Recycle the materials with the symbol . Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. VISIT OUR WEBSITE FOR: - Products - Brochures - User manuals - Trouble shooter - Service information www. aeg. com LEGEND Warning - Important Safety information. [. . . ] If you use the combi detergent tablets, activate the Multitab function. Be sure that these tablets are applicable to the water hardness in your area. Water hardness German degrees (°dH) 51 - 70 43 - 50 37 - 42 29 - 36 23 - 28 19 - 22 15 - 18 11 - 14 4 - 10 <4 French degrees (°fH) 91 - 125 76 - 90 65 - 75 51 - 64 40 - 50 33 - 39 26 - 32 19 - 25 7 - 18 <7 mmol/l Clarke degrees 64 - 88 53 - 63 46 - 52 36 - 45 28 - 35 23 - 27 18 - 22 13 - 17 5 - 12 <5 ADJUSTING THE WATER SOFTENER Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results. The dishwasher salt keeps the water softener clean and in good conditions. It makes sure that the water softener uses the correct quantity of dishwasher salt and water. You must adjust the water softener manually and electronically. Water softener adjustment Manual Electronic 10 9 8 7 6 51) 4 3 2 12) 9. 1 - 12. 5 7. 6 - 9. 0 6. 5 - 7. 5 5. 1 - 6. 4 4. 0 - 5. 0 3. 3 - 3. 9 2. 6 - 3. 2 1. 9 - 2. 5 0. 7 - 1. 8 < 0. 7 2 1) 2 1) 21) 21) 21) 21) 1 1 1 12) 1) Factory position. 2) Do not use salt at this level. ENGLISH 11 Manual adjustment Turn the water hardness dial to the position 1 or 2. Electronic adjustment 1. Turn the programme knob until the display shows two horizontal status bars. Press and hold Multitab and Delay at the same time until the indicators , , and flash. 5. Deactivate the appliance to confirm. FILLING THE SALT CONTAINER CAUTION!To prevent it, after you fill the salt container, start a programme. 1. Turn the cap clockwise to close the salt container. 12 FILLING THE RINSE AID DISPENSER A B CAUTION!The rinse aid, during the last rinsing phase, helps to dry the dishes without streaks and stains. C D 1. 3. M AX + 4 3 2 1 - 4. Press the release button (D) to open the lid (C). Fill the rinse aid dispenser (A), no more than the mark 'max'. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. Detergent tablets do not fully dissolve with short programmes and detergent residues can stay on the dishes. We recommend that you use detergent tablets with long programmes. • The display shows the programme duration that decreases with steps of 1 minute. Starting a programme with delay start 1. Press Delay again and again until the display shows the delay time you want to set (from 1 to 24 hours). • The display shows the countdown of the delay start that decreases with steps of 1 hour. – The indicator of the phase in operation comes on. SETTING AND STARTING A PROGRAMME Setting mode The appliance must be in setting mode to accept some operations. The appliance is in setting mode when, after the activation: • All the phase indicators come on. [. . . ] Make sure that you add detergent in the dispenser before you start a programme. Make sure that the set level of the water softener agrees with the water hardness in your area. Decrease the released quantity of rinse aid . The quantity of detergent was not sufficient. There was no detergent in the detergent dispenser. The salt container is empty. The set level of the water softener is incorrect. The cap of the salt container is loose. [. . . ]