User manual AEG-ELECTROLUX EKC6005

[. . . ] Consult the instructions booklet before installing and using the appliance. - This household appliance has been designed for cooking and it must therefore be used for this purpose only. This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. [. . . ] Fan oven Both the fan and the circular heating element operate together. The hot air is adjustable between 50 and MAX°C and is evenly distributed inside the oven. This is ideal for cooking several types of food (meat, fish etc) at the same time without affecting taste and smell. It is ideal for delicate pastries. 9 GB USE OF THE GRILL Install the grid on the third shelf from the oven bottom, at about 12 cm from the surface. USE OF THE TURNSPIT To use the turnspit follow the instructions below. Ensure that it is secured properly between the two forks F and balance it correctly to avoid unnecessary strain on the transmission R (fig 4). - Rest the spit on the support G, after having fitted the opposite end into socket P of the transmission R (fig 4) - Place the drip-tray with some water under the turnspit, on the lowest level. - To remove the spit, operate in the opposite direction using knob A and protecting gloves (see fig. 4 R P The shelf position can be changed as required depending on personal taste and the type of food. Heat the oven 5 minutes before introducing the food. 2 F L 1 A 1 G 10 GB INSTRUCTIONS FOR USE OF CLOCK LED PROGRAMMER (Fig. The + and - buttons increase or decrease the time at a speed depending on how long the button is pressed. Setting the time Press any two buttons (cooking time, end time, minute minder at the same time, and + or - button to set the desired time. 8). 960 1000 900 WARNINGS Do not use the oven door handle to move the appliance, for example to remove it from the packaging. IMPORTANT: Any adjacent furniture must be able to withstand high temperatures (min. If the appliance is to be installed near units, leave the minimum gaps specified in figure 7B . The cooker must not be placed on a pedestal To assemble legs, lift the cooker up and screw the four legs into the suitable threadings located at the corners on the underside of the appliance (fig 8). OK NO Fig. 400 mm GB TO FIX THE COOKER TO THE REAR WALL WARNING - For safety reasons and to prevent tipping of the appliance, these stabilizing means must be installed. The cooker is equipped with 2 chains fixed on each side at the rear of the cooker near the top (see Fig. The chains are fitted with spring clips which must be clipped to the screw eyes provided with the cooker. Insert part R into the holes then screw in the screw eyes part G see Fig. Note: If the part provided is not suitable for the wall material please use an appropriate device to ensure secure holding of the screw eyes to the wall. Bring the cooker near the wall and clip the chains on the screw eyes as in Fig. maintenance) resulting in the cooker being unclipped from the wall, the cooker must be re-clipped to the wall at the completion of the task. 55 mm 55 mm Position 2 Position 1 chain Position 3 Position 4 Fig. [. . . ] Open the mains terminal block cover as shown, unscrew screw A the cable clamp, and loosen the screws in the mains terminal block L N E which secure the three wires of the mains cable. Allow sufficient cable length for the cooker to be pulled out for cleaning, but do not let it hang lower than 50mm (2) from the floor. The cable can be looped if necessary, but make sure that it is not kinked or trapped when the cooker is in position. IMPORTANT The wires in the mains cable are coloured as follows: GREEN AND YELLOW . . . . . EARTH BLUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NEUTRAL BROWN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . LIVE REPLACING OF THE CABLE If the cable becomes damaged or worn, replace it, observing the following instructions: - open the box of the supply board (see fig. 16A); - unscrew screw A that secures the cable; - replace the cable with one of the same length and which corresponds to the features described in the table; switch the appliance off, and shut the gas tap; - connect the green-yellow earth wire to the terminal , leaving it approximately 10 mm longer than the live wire; - connect the blue neutral wire to the terminal marked N; - connect the live wire to the terminal marked L. Fig. [. . . ]