User manual AEG-ELECTROLUX 79200KF-N 00J

[. . . ] 27 3 Operating Instructions 1 Safety instructions 3 5 Please comply with these instructions. This appliance conforms with the following EU Directives: ­ 73/23/EEC dated 19. 02. 1973 Low Voltage Directive ­ 89/336/EEC dated 03. 05. 1989 EMC Directive inclusive of Amending Directive 92/31/EEC ­ 93/68/EEC dated 22. 07. 1993 CE Marking Directive Correct use · This appliance should be used only for normal domestic cooking and frying of food. · The appliance must not be used as a work surface or as a storage surface. · Additions or modifications to the appliance are not permitted. [. . . ] If other timer functions are set, after a few seconds the shortest remaining time of all the timer functions is displayed and the corresponding pilot light flashes. Control panel Select zone Touch or Indicator cooking Pilot light for the cooking zone selected flashes 00 to 99 minutes After a few seconds the pilot light flashes more slowly. Control panel Select zone Touch Indicator cooking Pilot light of cooking zone selected flashes faster Time remaining is displayed The time remaining counts backwards to 00. 2. The pilot light goes out. The Timer function for the selected cooking zone is switched off. Changing the time Step 1. Control panel Select zone Touch or Indicator cooking Pilot light of the selected cooking zone flashes faster Time remaining is displayed 2. 01 to 99 minutes After a few seconds, the pilot light flashes more slowly. The time counts down. 14 Displaying the time remaining for a cooking zone Step 1. zone Control panel field Display Select cooking Pilot light of the cooking zone selected flashes faster The time remaining is displayed After a few seconds the pilot light flashes more slowly. Switching off the acoustic signal Step 1. Control panel field Touch Acoustic signal Acoustic signal to acknowledge. Acoustic signal stops. 15 Safety cut-out Cooking surface · If after switching on the cooking surface, a heat setting is not set for a cooking zone within approx. · If one or more sensor fields are covered by objects (a pan, cloths, etc. ) for longer than approx. 10 seconds, a signal sounds and the cooking surface switches off automatically. · If all cooking zones are switched off, the cooking surface automatically switches itself off after approx. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. 2 W 22 Installation Instructions Safety instructions The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc. ) Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed. Anti-shock protection must be provided by the installation, for example drawers may only be installed with a protective floor directly underneath the appliance. The cut surfaces of the worktop are to be protected against moisture using a suitable sealant. Otherwise hot cookware may be knocked off the rings when doors and windows are opened. · Ensure anti-shock protection through correct installation by a qualified electrician. · The appliance must be connected to the electrical supply by a qualified electrician. Loose and inappropriate plug and socket connections can make the terminal overheat. · Have the clamping joints correctly installed by a qualified electrician. · In the event of single-phase or two-phase connection, the appropriate mains cable of type H05BB-F Tmax 90°C(or higher) must be used. [. . . ] The statutory warranty does not apply when defects are caused by: · a chemical or electrochemical reaction caused by water, · abnormal environmental conditions in general, · unsuitable operating conditions, · contact with harsh substances. The guarantee does not apply to defects due to transport which have occurred outside of our responsibility. Nor will the guarantee cover those caused by inadequate installation or assembly, lack of maintenance or failure to respect the assembly instructions or directions for use. Defects that result from repairs or measures carried out by people who are not qualified or expert or defects that result from the addition of non-original accessories or spare parts are not covered by the guarantee. [. . . ]