User manual ACER X213

[. . . ] 8 Connector Pin Assingment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Standard Timing Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 User controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 How to adjust a setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 X213W SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES · Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. · You may find slightly uneven brightness on the screen depending on the desktop pattern you use. [. . . ] · Adjust the display brightness and/or contrast to a comfortable level for enhanced text readability and graphics clarity. · Eliminate glare and reflections by: · placing your display in such a way that the side faces the window or any light source · minimizing room light by using drapes, shades or blinds · using a task light · changing the display's viewing angle · using a glare-reduction filter · using a display visor, such as a piece of cardboard extended from the display's top front edge · Avoid adjusting your display to an awkward viewing angle. · Avoid looking at bright light sources, such as open windows, for extended periods of time. Developing good work habits Develop the following work habits to make your computer use more relaxing and productive: · Take short breaks regularly and often. ----------------------------------------------------------------------------------------------------Warning!If this is unavoidable, work for only short periods, take breaks regularly, and do some stretching exercises. ----------------------------------------------------------------------------------------------------For more information and help in recycling, please visit the following websites: Worldwide: http://global. acer. com/about/sustainability. htm EN-4 X213W UNPACKING Please check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or transport the monitor in future. · LCD Monitor · 15-pin D-Sub Cable · DVI Cable (Only Dual-Input Model) · AC Power Cord · User Manual · Quick Start Guide X2 13W P/N:MU. LCG00. 001 X213W 2008 EN-5 X213W Attaching / Removing the Base Install: Align the release button on the bottom of the monitor with the corresponding slots on the bottom of the base. Remove: Depress the release button as indicated first before removing the base and follow the arrow direction to remove it. SCREEN POSITION ADJUSTMENT In oder to optimize the best viewing position, you can adjust the tilt of the monitor by using both of your hands to hold the edges of the monitor as shown in the figure below. The monitor can be adjusted to 15 degrees up or 5 degrees down as indicated by arrow below. EN-6 X213W CONNECTING THE POWER CORD · Check first to make sure that the power cord you use is the correct type required for your area. · This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240 V AC voltage area. · Plug one end of the power cord to the AC Inlet, plug another end to a proper AC outlet. · For unit using at 120 V AC: Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V. · For unit using at 220/240 V AC (outside of U. S. ): Use a Cord Set consisting of H05VV-F cord and plug rated 10 A, 250 V. The cord set should have the appropriate safety approvals for the country in which the equipment will be installed. SAFETY PRECAUTION · · · · Avoid placing the monitor, or any other heavy object, on the power cord to avoid damage to the cable. Always put the monitor in a place where there is adequate ventilation. Avoid placing the monitor against a bright background or where sunlight or other light sources may reflect on the face of the monitor. Refrain from giving shock or scratch to the screen, as screen is fragile. · · CLEANING YOUR MONITOR Please carefully follow the below guidelines when cleaning the monitor. · Use a soft cloth to wipe the screen and cabinet front and sides. EN-7 X213W Power saving The monitor will be driven into Power Saving" mode by the control signal from the display controller, as indicated by the amber-color power LED. State ON Power Saving Mode LED Light Blue Amber The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated. Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer's port. Connect power cord Connect the power cord to the monitor, then to a properly grounded AC outlet. Power-ON Monitor and Computer Power-ON the monitor first, then power-ON the computer. [. . . ] The following local Manufacturer /Importer is responsible for this declaration: Product: Model Number: SKU Number: Name of Responsible Party: 22" LCD Monitor X213W X213W xxx ("x" = 0~9, a ~ z, or A ~ Z) Acer America Corporation Address of Responsible Party: 333 West San Carlos St. Contact Person: Phone No. : Fax No. : Acer Representative 254-298-4000 254-298-4147 EN-22 X213W X213W 3F, No. 168 Xizang medium road, Huangpu District, Shanghai, China Acer Computer (Shanghai) Limited Declaration of Conformity We, Acer Computer (Shanghai) Limited 3F, No. 168 Xizang medium road, Huangpu District, Shanghai, China Contact Person: Mr. [. . . ]