User manual ACER PD116
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ACER PD116. We hope that this ACER PD116 user guide will be useful to you.
You may also download the following manuals related to this product:
ACER PD116 (1915 ko)
ACER PD116 (1382 ko)
ACER PD116 (1905 ko)
ACER PD116 (1383 ko)
ACER PD116 (1911 ko)
Manual abstract: user guide ACER PD116
Detailed instructions for use are in the User's Guide.
[. . . ] Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Usage Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the "TEMP" indicator flashs red for about 10 seconds, you will see a message "Fan fail. Lamp will automatically turn off soon. " on the on-screen display. Please contact your local dealer or our service center.
English . . . 12
Installation
Adjusting the Projected Image
Adjusting the Projector Image Height
The projector is equipped with an elevator foot for adjusting the image height.
To raise the image: 1. Raise the image to the desired height angle , then release the button to lock the elevator foot into position. Lower the image, then release the button to lock the elevator foot into position. 4 Confirm your selection of items.
Four Directional Select Keys
4 Use
to select items or make adjustments to
your selection.
15 . . . English
User Controls
Using the Remote Control Power
4 Refer to the "Power On/Off the Projector" section on pages
11-12.
Empowering Key
4 Display the "Display Mode" submenu of the onscreen display
menu to select display mode from PC, Movie, sRGB and User directly.
Menu
4 Press "Menu" to launch the on screen display menu. To exit
OSD, press "Menu" again.
Four Directional Selec t Keys
4 Use
to select items or make adjustments to
your selection.
Laser Button
4 Aim the remote at the viewing screen, press and hold this
button to activate the laser pointer.
Mute
4 Momentarily turns off the audio.
Keystone + / degrees).
4 Adjusts image distortion caused by tilting the projector (±16
Page Up (Computer mode only)
4 Use this button to page up. This function is only available
Page Down (Computer mode only)
when the projector is connected to a computer via an USB cable.
4 Use this button to page down. This function is only available
Re-Sync
when the projector is connected to a computer via an USB cable.
4 Automatically synchronizes the projector to the input source.
Hide
4 Momentarily turns off the video. Press "Hide" to hide image,
press again to restore display of the image.
Source
4 Press "Source" to choose RGB, Component-p, Component-i,
S-Video, Composite Video and HDTV sources.
Freeze
4 Press "Freeze" to pause the screen image.
English . . . 16
User Controls
On Screen Display Menus
The Projector has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source.
How to operate
1. To open the OSD menu, press "Menu" on the Remote
Control or press "Menu/Enter"on the Control Panel.
2. When OSD is displayed, use
keys to select any item in the
main menu. After selecting the desired main menu item, press to enter sub menu for feature setting.
3. Use
settings by
keys to select the desired item and adjust the key.
4. Select the next item to be adjusted in the sub menu and adjust as
described above.
5. Press "Menu" on the Remote Control or press "Menu/Enter"on
the Control Panel, the screen will return to the main menu.
6. To exit OSD, press "Menu" on the Remote Control or press
"Menu/Enter"on the Control Panel again. The OSD menu will close and the projector will automatically save the new settings.
Main Menu
Sub Menu
Settings
17 . . . [. . . ] 28
Appendices
Problem: The image is outstretched when displaying 16:9 DVD.
The projector automatically detects 16:9 DVD and adjusts the aspect ratio by digitizing to full screen with 4:3 default setting. If the image is still outstretched, you will also need to adjust the aspect ratio by referring to the following: 4 Please select 4:3 aspect ratio type on your DVD player if you are playing a 16:9 DVD. 4 If you can't select 4:3 aspect ratio type on your DVD player, please select 4:3 aspect ratio in the on screen menu.
Problem: Image is reversed.
4 Select "Management" from the OSD and adjust the projection
direction. See page 25.
Problem: Lamp burns out or makes a popping sound
4 When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ACER PD116
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ACER PD116 will begin.