User manual 3J USB-W1D

[. . . ] (2) Press pressing : Hang up (1) End a call or refuse an incoming call. : Press to input "+" at ready state, else input "*". : Press to scroll ring style at ready state, else input "#". to put a call on hold, release the call by again. Speaker light: (1) During a call via handset, pressing the Handfree key, the speaker light will flash. [. . . ] (3) Input number and call out: Press digital "11" on the handset's keypad, then press call out. 2. 6. 5 Call to regular phone Press "00" + "country number" + "phone number", then press . Example: call someone in Beijing, China, please press 00861012345678, and then press 0086 ---------------country code Note: 10 ---------city code . 12345678 -------------------destination number to to 2. 7 Answer a call 2. 7. 1 Answer a call via handset When a call comes in, both of the base and the handset will ring. Press to answer the call, or press to refuse it. 2. 7. 2 Answer a call via base (1) When a call comes in, both the base and the handset will ring. (2) Press Handfree key again to end the call. (1) You can input "+" instead of "00". (2) If you want to use this function, you should buy SkypeOut Credit from www. skype. com first. 10 11 2. 8 State Instruction (1) Ready state a. Missed call 2. 9 Advanced (1) Right click the icon on the taskbar and select Advance (2) The window is shown as below: (2) The icons displayed in call list a. Missed call (3) Battery condition (3) Run when Windows starts: Select to enable this feature. SkypeOut The SkypeMate will be launched automatically when Windows starts. (4) Refuse Skype call when Skype talking: Select to enable this feature. (5) Display Skype window when calling (see the picture in below page): If you cancel this option, when you press the digital keys 0-9, *, #, the Skype windows will not pop up (except incoming call and outgoing call). 12 13 2. 10 Auto-select RF channel This function is effective to improve the quality of handset's voice. The handset will change the RF channel automatically when the voice is not so good. (1) Right click the icon on the taskbar and select Advance (2) The window is shown as below: (2) The window is shown as below: (3) Enter the number from the PC's keypad. Note: The USB Wireless Phone used in one room should use different channel, please make sure to select a channel which is not used by other USB Wireless Phone. (4) Click the button "OK" to save the setup. (3) Select Auto selection RF Channe to enable this function. 2. 11 Select RF channel by manual If there is more than one USB Wireless Phone in the room, and the quality of the voice is not so good, please select the RF channel by manual. 14 15 3 FAQ Problem 1 There is no ring can be heard or the ring tone is too low. Solution (1) Go to Skype, run "Tools-> Options->Sounds", select "Play sound". Open mySkypeRing. wav (3) Select "ringtone" at the "When" box which is on the top of the window (4) Select "Play sound", which is under the "When" box (5) Select mySkypeRing at the box beside "Play sound" (6) Click the "Save" button to save and end the setting. Problem 2 I am not able to hear any sound through the earphone?Solution Please execute the "Control Panel->Sound and Video ( ->Audio", set Sound Playback and Sound Recording's preference device to your sound card. [. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. [. . . ]